
( Brand: Wintec ), ( Manufacturer Part Number: 35944581-L ), ( Type: Ddr1 Sdram ), ( Number Of Pins: 184 ), ( Capacity Per Module: 512mb ), ( Bus Speed: Pc2700 ), ( Memory Features: Ecc Memory )
Experience a seamless upgrade to your system's memory with the Wintec DDR3-333MHz PC2-5400 4GB (2 x 2GB) ECC DIMM Kit. Designed to cater to high-performance computing needs, this memory module boosts your system's efficiency, enhancing overall system stability and reliability.
The kit features two 2GB DIMMs, providing a total capacity of 4GB. Each module operates at a speed of DDR3-333MHz, translating to a data transfer rate of PC2-5400, ensuring swift and efficient data handling. This memory is ideal for businesses, server applications, and power users who demand rock-solid stability and unwavering data integrity.
The Wintec DDR3 memory module adheres to the 184-pin DIMM standard, ensuring compatibility with a wide range of systems. Specifically designed for platforms that require ECC (Error-Correcting Code), this memory kit minimizes data errors and corrects single-bit errors on-the-fly, further enhancing system stability and reliability.
With a voltage of 1.5V, this memory module is designed to be energy-efficient, reducing heat output and lowering power consumption. The Wintec DDR3-333MHz PC2-5400 4GB (2 x 2GB) ECC DIMM Kit carries the model numbers 35944581 and 35944581-L, making it an easy addition to your system for enhanced performance, stability, and reliability. Upgrade your system with this high-performance memory solution from Wintec today!
Product: Wintec DDR333 4GB Kit (35944581) - ECC 184-pin DIMM Set
Pros:1. Cost-effective: This RAM kit is relatively affordable, making it a budget-friendly option for those looking to upgrade their system memory.
2. ECC (Error Correcting Code) RAM: ECC RAM is designed to detect and correct errors in data during computer memory read and write cycles, making it suitable for systems that require high data integrity such as servers or workstations.
3. Dual-Channel Ready: This RAM is designed to be used in pairs, allowing for improved performance when used in a dual-channel configuration in compatible motherboards.
4. Compatibility: The RAM is compatible with various systems that support DDR3 184-pin DIMM and runs at PC2700 (667MHz).
Cons:1. Speed: DDR333 is one of the slowest speeds for DDR3 RAM, which may lead to slower performance compared to newer, faster RAM.
2. Latency: The latency, or delay, in this RAM may be higher due to its lower speed, which could affect system performance in some applications.
3. Capacity: 4GB of RAM may not be sufficient for power users, gamers, or heavy multitaskers who require more memory for their tasks.
4. Compatibility Limitations: This RAM may not be compatible with all motherboards, especially those that support newer DDR4 RAM.
Ending Conclusion:The Wintec DDR333 4GB Kit is a cost-effective solution for those in need of ECC RAM for servers or workstations that require high data integrity. However, its lower speed and capacity may limit its performance and suitability for other types of systems or users requiring faster speed and higher capacity.
Recommendation:If you're looking for a cost-effective ECC RAM for server or workstation use, the Wintec DDR333 4GB Kit could be a suitable choice. However, if you need faster speed or higher capacity, you may want to consider a more expensive option or upgrading to DDR4 RAM. Always ensure compatibility with your motherboard before making a purchase.
The 8 chips are a matched set, each chip is 512mb for total of 4gb ram. But when they were pulled still working fine, and promptly stored away. Working and in good condition, last tested when they were removed from the system. The board that these came out of had eight memory sockets so all 8 chips were used at once.
These were used in a Ryan workstation server for 3 years until they replaced to extend memory capacity. I no longer have the system to recheck them.